3DMark 06 Scores

[Dragon]

i am goin to guess bout 1.8 - 2.0 volts . for me to get to 4.1 need 1.8 volts granted every chip is different but thats way to many volts for these quads .

[{uZa}D.O.A.]

That is 2x 8800GTS cards correct?

Correct!

[Limbo]

What kind of voltage did you have to push to run 4.5 on the q6600 Limbo?

It is an E8400 Methious. About 1.58 or 1.6V in BIOS I think it was, my CPU-Z screenie shows only 1.568 in Windows though. It won't boot on air at 1.65V and this board increases a 1/2 volt at a time after 1.6V. Don't try this unless you are willing to lose something of value in your rig, I was trying with all my might to beat: http://www.bjorn3d.com/forum/showpos...&postcount=636

But I failed miserably....

[Dragon]

that took a lil bit of work to do . have you ever considered running water ?

[Limbo]

that took a lil bit of work to do . have you ever considered running water ?

Not seriously, thought more about a DICE or LN2 pot to be truthful but doubt I will ever go that far.

[srpeters18]

You should consider water. I'm running 1.54v full load on a quad (about 1.62 in BIOS) and my load temp, with a 27C ambient, is right at 60C

[ol'norton]

Not seriously, thought more about a DICE or LN2 pot to be truthful but doubt I will ever go that far.

You should have said, I have an F1 pot you can have if you want to get a new bracket from Vince.

[Limbo]

You should have said, I have an F1 pot you can have if you want to get a new bracket from Vince.

Seriously? I was hoping to see you get evil on that FoxConn/QX9650 with it at least once Ol'norton. If I had a template a bracket shouldn't be too hard to make..... I am thinking a new mobo would be a necessity in my case as well because of the limited FSB on this P35-DQ6???

EDIT: This one is pretty: [XF]ASUS X58 series, ture 16+2 phase PWM - P6T Deluxe

[ol'norton]

K|ngp|n is sending me a new bracket.
I would do a couple of runs with the DQ6 first, before trying an expensive new board. You'll probably get a bit more fsb on dice anyway.
But if you do go 1366pin, you'll have to make a new top & bottom bracket.
PM me your address again.

[Limbo]

Address sent, hope you reconsider though as it is a no-brainer that in your hands it could be a far more valuable tool.

[Limbo]

21126 0n air: http://service.futuremark.com/compare?3dm06=8258170

[Dragon]

Very nice score limbo ... i am having issues on viewing your details tho ..

[Limbo]

Very nice score limbo ... i am having issues on viewing your details tho ..

Thanks Raptor and my bad on the link , does it work now?

[Dragon]

you welcome , and yeppers it is now good job again .... crank it like you stolle it

[the_dope_chaud]

GODANG !
A ln2 pot on bjorn !
yay....
Can't believe I missed that. I would love to bench with DI or ln2, many times I have talked to shwarz about having a OC club in montreal. Unfortunately, I'm leaving to mexico and I'm gonna forget about that for a while, but when my life will afford it, I will do. I can't wait to see that F1 pot used on bjorn, and bravo for wanting to give it and spread the love !


Sorry to be so